Reference: Appliance Lights, Ports, and Specifications
  
Reference: Appliance Lights, Ports, and Specifications
Knowing what status lights indicate, where the appliance ports are located, and the appliance’s physical specifications can help you understand how to properly connect your appliance to a network, keep it running optimally, and when it needs maintenance. Use this reference to understand your appliance’s lights, ports, and specifications.
2U xx80 appliances
This section describes the status lights, port locations, and technical and environmental specifications for the 2U 5080 and 7080 appliances.
Status lights and port locations
This section provides front and back views of the 2U xx80 appliances and describes the status lights, port locations and buttons.
Front panel 2U xx80 appliance
This table summarizes the LEDs and buttons on the front of the appliance.
Reference
LED/button
Description
1
Power On/Off Button and Integrated LED
On = Green (System is turned on.)
Sleep State = Green (System is in S1 or S3 sleep state.)
Off = No light (Power is off.)
2
IPMI Warning LED
The IPMI Warning LED shows the current health of the server system.
Normal = Green (No failures)
Degraded/Warning = Amber (Indicates fan failure, high temperature, over voltage, or power supply failure.)
Critical = Blinking Amber and Green (Indicates a problem that needs attention, such as optimization service down, no license, or in_path is not enabled for optimization service.)
3
ID LED
On = Blue (System identified remotely on the server.)
Off = Off (System not identified.)
4
Reset Button
Press to reboot the appliance.
5
System ID Button
Press the system ID button when the system AC (Alternating Current) is on. The system ID LED indicates the system is identified with a blue light. Users from a remote site can activate the ID LED by inputting commands in IPMI. For details, contact Support at https://support.riverbed.com.
6, 7
USB Ports v2.0
 
8
HDD/SSD LEDs
Activity LED (lower light)
Link = Green (Drive present, with no activity.)
Activity = Blinks green (Drive present, with activity.)

Status LED (upper light)
Failed Disk = Solid Red
This figure illustrates the back of the appliance, including the ports.
Back panel 2U xx80 appliance
By default, the SteelHead CX 5080 and CX 7080 ship with a bypass card in slot 3. The default interface names are WAN3_1, LAN3_1, WAN3_0, LAN3_0.
For slots 4, 5, and 6, the interface ports are reversed. For example, for slot 4 the interface ports would be LAN4_0, WAN4_0, LAN4_1, WAN4_1.
This table summarizes the status lights and ID button on the back of the appliance.
LED/button
Description
ID LED/Button
On = Blue (System identified remotely on the server.)
Off = Off (System not identified.)
Press the system ID button when the system AC (Alternating Current) is on. The system ID LED indicates the system is identified with a blue light. Users from a remote site can activate the ID LED by inputting commands in IPMI. For details, contact Support at https://support.riverbed.com.
Primary and AUX Port LEDs
Left LED
Link = Green
Activity = Blinks green
No Link = Off

Right LED
10 Mbps = Off
100 Mbps = Green
1000 Mbps = Amber
Four-Port 1 GbE Copper Bypass Card LEDs (preinstalled)
Link/Activity LED
Link = Green
Activity = Blinks green

Speed/Bypass/Disconnect LED
1000 Mbps = Yellow
100 Mbps = Green
10 Mbps = Off
Bypass = Blinks green
Disconnect = Blinks yellow
Power Supply LEDs
Power On and Healthy = Green
Standby = Blinks green
Power Off = Off
Unplugged or power lost but second power supply has power = Amber (for about 5 seconds) then turns Off
Power on with warning = Blinks amber (indicates high temperature, high power, high current, or slow fan)
Hardware specifications
This table summarizes the hardware specifications for the systems.
Specification
5080
7080
Form factor
2U
2U
Memory
32 GB (4 x 8 GB)
B010 = 64 GB (8 x 8 GB)
B020 = 96 GB (12 x 8 GB)
B030 = 192 GB (12 x1 6 GB)
HDD
2 x 1 TB
2 x 1 TB
SSD
6 x 240 GB
B010 = 6 x 480 GB
B020 = 8 x 480 GB
B030 = 8 x 960 GB
Data store
1.4 TB
B010 = 2.8 TB
B020 = 3.8 TB
B030 = 7.6 TB
Dimensions (LxWxH)
27.56 x 17.32 x 3.43 in. (700 x 440 x 87 mm)
27.56 x 17.32 x 3.43 in. (700 x 440 x 87 mm)
Weight (without packaging)
51 lb (23 kg)
51 lb (23 kg)
Voltage
100-127 V, 200-240 V
100-127 V, 200-240 V
PSU
 
2 x 770 W
100-127 VAC/10 A, 50/60 Hz
200-240 VAC/5 A, 50/60 Hz
2 x 770 W
100-127 VAC/10 A, 50/60 Hz
200-240 VAC/5 A, 50/60 Hz
PCI slots
6
6
Included bypass ports/max # ports
4/20
4/20
Power consumption specifications
This table summarizes the power specifications for the systems. The systems are rated at the following power characteristics when operating at nominal AC input voltages (120 V and 230 V).
System
CX 5080
CX 7080
CX 7080
Configuration
B010
B010, B020
B030
PSU type
2 x 770 W
2 x 770 W
2 x 770 W
AC input
120 V
230 V
120 V
230 V
120 V
230 V
Max. amps.
3.2 A
1.7 A
3.9 A
2.0 A
5.0 A
2.6 A
Max. watts
372 W
363 W
467 W
455 W
598 W
574 W
Typical watts
298 W
290 W
374 W
364 W
478 W
459 W
Max. volt-ampere
383 VA
395 VA
477 VA
473 VA
604 VA
592 VA
Power factor
97 W/VA
92 W/VA
98 W/VA
96 W/VA
99 W/VA
97 W/VA
BTU (typical)
1015 BTU
991 BTU
1275 BTU
1240 BTU
1632 BTU
1566 BTU
Environmental specifications
This table summarizes the environmental requirements for the systems.
Specification
5080
7080
Operating acoustic
56 dB (typical)
56 dB (typical)
Temperature (operating)
32° to 104°F (0°- 40°C)
32° to 104°F (0°- 40°C)
Temperature (storage)
-40° to 140°F (-40°- 60°C)
40° to 140°F (-40°- 60°C)
Relative humidity
40% to 90%, noncondensing at 40°C
40% to 90%, noncondensing at 40°C
2U 9800 appliances
This section describes the status lights, port locations, and buttons on the front and back of the 2U 9800 appliance. The technical, power consumption, and environmental specifications for the 2U 9800 are the same as the specifications for 2U xx80 appliances (see 2U xx80 appliances).
Status lights and port locations
This section provides front and back views of the 2U 9800 appliances and describes the status lights, port locations and buttons.
Front panel 2U 9800 appliances
This table summarizes the LEDs and buttons on the front of the Interceptor 9800 appliance.
Reference
LED/button
Description
1
Power On/Off Button and Integrated LED
On = Green (System is turned on.)
Sleep State = Green (System is in S1 or S3 sleep state.)
Off = No light (Power is off.)
2
IPMI Warning LED
The IPMI Warning LED shows the current health of the server system.
Normal = Green (No failures)
Degraded/Warning = Amber (Indicates fan failure, high temperature, over voltage, or power supply failure.)
Critical = Blinking Amber and Green (Indicates a problem that needs attention, such as optimization service down, no license, or in_path is not enabled for optimization service.)
3
ID LED
On = Blue (System identified remotely on the server.)
Off = Off (System not identified.)
4
Reset Button
Press to reboot the appliance.
5
System ID Button
Press the system ID button when the system AC (Alternating Current) is on. The system ID LED indicates the system is identified with a blue light. Users from a remote site can activate the ID LED by inputting commands in IPMI. For details, contact Support at https://support.riverbed.com.
6, 7
USB Ports v2.0
 
8
HDD/SSD LEDs
Activity LED (lower light)
Link = Green (Drive present, with no activity.)
Activity = Blinks green (Drive present, with activity.)

Status LED (upper light)
Failed Disk = Solid Red
Figure: Back panel 2U 9800 appliances shows the back panel status lights and port locations on the Interceptor 9800 appliance.
Back panel 2U 9800 appliances
This table summarizes the status lights and ports on the back of the Interceptor 9800 appliance.
LED/button
Description
ID LED/Button
On = Blue (System identified remotely on the server.)
Off = Off (System not identified.)
Press the system ID button when the system AC (Alternating Current) is on. The system ID LED indicates the system is identified with a blue light. Users from a remote site can activate the ID LED by inputting commands in IPMI. For details, contact Support at https://support.riverbed.com.
Primary and AUX Port LEDs
Left LED
Link = Green
Activity = Blinks green
No Link = Off

Right LED
10 Mbps = Off
100 Mbps = Green
1000 Mbps = Amber
Four-Port 1 GbE Copper Bypass Card LEDs (preinstalled)
Link/Activity LED
Link = Green
Activity = Blinks green

Speed/Bypass/Disconnect LED
1000 Mbps = Yellow
100 Mbps = Green
10 Mbps = Off
Bypass = Blinks green
Disconnect = Blinks yellow
Power Supply LEDs
Power On and Healthy = Green
Standby = Blinks green
Power Off = Off
Unplugged or power lost but second power supply has power = Amber for about 5 seconds, and then turns Off
Power on with warning = Blinks amber to indicate high temperature, high power, high current, or slow fan.
1U 3080 appliances
This section describes the status lights, port locations, buttons, and technical and environmental specifications for the SteelHead 1U 3080 appliance.
Status lights and port locations
This section provides front and back views of the status lights, port locations, and buttons on the 1U 3080 appliance. Figure: Front panel 3080 appliance illustrates the front of the appliance.
Front panel 3080 appliance
This table summarizes the LEDs and buttons on the front of the appliance.
LED or button
Description
Power On/Off Button and Integrated LED
On = Blue (System is turned on.)
Sleep State = Yellow (System is in S5 sleep state.)
Off = No light (Power is off.)
System LEDs
The combination of LED 1 and LED 2 defines the system state:
LED 1 = Yellow, LED 2 = Yellow, System State = Critical
LED 1 = Yellow, LED 2 = Green, System State =Degraded
LED 1 = Green, LED 2 = Green, System State = Healthy
LED 3 - Not used; default is off
LED 4 - Not used; default is off
Reset Button
Press to restore factory defaults.
Console port
RJ45 port
USB Ports v3.0
1 - USB Type A port
1 - USB Type C port
Port 1 PRI = Primary port
Left LED
Link = Green
Activity = Blinks green
Right LED
10 Mbps data rate = No light (with link on left LED)
100 Mbps data rate = Green
1000 Mbps data rate = Yellow
Port 2 AUX = Auxiliary port
Left LED
Link = Green
Activity = Blinks green
Right LED
10 Mbps data rate = No light (with link on left LED)
100 Mbps data rate = Green
1000 Mbps data rate = Yellow
Ports 3-6 LAN/WAN ports
Left LED
Link = Green
Activity = Blinks green
Bypass/Disconnect = Yellow
Right LED
10 Mbps data rate = No light (with link on left LED)
100 Mbps data rate = Green
1000 Mbps/1 Gbps = Yellow
Ports 7-8 (on-board)
Not used.
Figure: Back panel 3080 appliance illustrates the back of the appliance, including the ports.
Back panel 3080 appliance
This table summarizes the status lights and ID button on the back of the appliance.
LED/button
Description
HDDs
Activity LED (upper light)
Activity = Blinks green (drive present, with activity.
Status LED (lower light)
Failed Disk = Solid amber
Power Supply LEDs
Power On and Healthy = Green
Standby = 1 Hz blinks green
Power Off = Off
Unplugged or power lost but second power supply has power = Amber (for about 5 seconds) then turns Off
Power on with warning = 1 Hz blinks amber (Indicates high temperature, high power, high current, or slow fan.)
Hardware specifications
This table summarizes the hardware specifications for the systems.
Specification
1U 3080
Form factor
1U rack mountable unit
RAM
24 GB
HDD
2 x 1 TB
SSD
1x 32 GB (for boot)
Data store
400 GB
Dimensions (LxWxH)
15.25 x 17.24 x1.73 in (387.35 x 483 x 44 mm)
Weight (without packaging)
27 lb (12.25 kg)
Power (Typical)
70 W
BTU
242
Voltage
100-240 V
PSU
2 x hot-swappable/redundant, 550W
W = 100-240 VAC/7.1/3.4A, 47-63 Hz
PCIe slots
1 FHFL (full height/full length)
Bypass ports/maximum #
4 (on-board) / 8 (with add-on card)
Power consumption specifications
This table summarizes the power specifications for the systems. The systems are rated at the following power characteristics when operating at nominal AC input voltages (120 V and 230 V).
System
1U 3080
PSU type
2 x 550 W
AC input
120 V
240 V
Max. watts
88.7 W
73.8 W
Max. amps.
0.9144 A
0.488 A
Power factor
98.58 W/VA
95.6 W/VA
Max. volt-ampere
89.97 VA
77.19 VA
Typical watts
70.96 W
59.04 W
BTU (typical)
241.97 BTU
201.32 BTU
Environmental specifications
This table summarizes the environmental requirements for the systems.
Specification
CX 3080
Operating acoustic
45 dB (typical)
Temperature (operating)
32° to 113°F (0° to 45°C)
Temperature (storage)
-40° to 149°F (-40° to 65°C)
Relative humidity
20% to 80%, noncondensing (Operating)
10% to 95%, noncondensing (Storage)
Desktop x80 appliances
This section describes the ports, LEDs, technical and environmental specifications for the desktop x80 (platform family) appliances.
Status lights and port locations
These figures illustrate the port locations, LEDs, and buttons.
Front panel Desktop x80
Back panel Desktop x80
This table summarizes the front port locations, status lights, and buttons.
Front LEDs and buttons
Status
Power Button LED
On = Blue (system is turned on)
Sleep State = Yellow (system is in S5 sleep state)
Off = No light (power is off)
System LEDs
The combination of LED 1 and LED 2 defines the system state:
LED 1 = Yellow, LED 2 = Yellow, System State = Critical
LED 1 = Yellow, LED 2 = Green, System State =Degraded
LED 1 = Green, LED 2 = Green, System State = Healthy
LED 3 - Not used; default is off
LED 4 - Not used; default is off
Reset button
Restores system to factory defaults.
Console port
RJ45 port
USB ports v3.0
1 - USB Type A port
1 - USB Type C port
Port 1 PRI
Left LED = Link/Bypass
Link = On (Solid green)
Activity =Blinks green
Right LED= Speed
10 Mbps data rate = Off
100 Mbps data rate = Green
1000 Mbps data rate = Amber
Port 2 AUX
Left LED = Link/Bypass
Link = On (Solid green)
Activity =Blinks green
Right LED = Speed
10 Mbps data rate = Off
100 Mbps data rate = Green
1000 Mbps data rate = Amber
Ports 3-6: LAN/WAN LEDs
Left LED
Link = Green
Activity = Blinks green
Bypass/Disconnect = Yellow
Right LED
10 Mbps data rate = No light (with link on left LED)
100 Mbps data rate = Green
1000 Mbps/1 Gbps = Yellow
Ports 7-8 (on-board)
Not used.
This table summarizes the status lights and ID button on the back of the appliance.
LED/button
Description
Power Supply LEDs
Power On and Healthy = Green
Standby = 1 Hz blinks green
Power Off = Off
Power lost but second power supply has power = Amber
Power on with warning = 1 Hz blinks amber (indicates high temperature, high power, high current, or slow fan)
Hardware specifications
This table summarizes the hardware specifications for the systems.
Specification
580 Desktop
780 Desktop
Power Watt
(typical)
37 W
60 W
BTU
128 BTU
205 BTU
RAM
16 GB
16 GB
HDD
1 x 1 TB
1 x 1 TB
SSD
1 x 32 GB (for boot)
1 x 32 GB (for boot)
Data store
200 GB
200 GB
Dimensions (LxWxH)
12.25 x 13.75 x 1.73 in.
311.15 x 349.25 x 44 mm
12.25 x 13.75 x 1.73 in.
311.15 x 349.25 x 44 mm
Weight (without packaging)
6 lb (2.7 kg)
6 lb (2.7 kg)
Voltage frequency
100-240 V/2.5 A
50/60 Hz
100-240 V/2.5 A
50/60 Hz
PSU
1 x Internal, 200 W
100-240 VAC/2.5 A, 50/60 Hz
1 x Internal, 200 W
100-240 VAC/2.5 A, 50/60 Hz
Onboard bypass ports/max # ports
4
4
Power consumption specifications
This table summarizes the power specifications for the desktop systems. The systems are rated at the following power characteristics when operating at nominal AC input voltages (120 V and 230 V).
System
CX 780
PSU type
2 x 550 W
AC input
120 V
240 V
Max. watts
75.1 W
60.7 W
Max. amps.
0.7692 A
0.39 A
Power factor
99 W/VA
95.2 W/VA
Max. volt-ampere
75.85 VA
63.76 VA
Typical watts
60.08 W
48.56 W
BTU (typical)
204.87 BTU
165.58 BTU
System
CX 580
PSU type
2 x 550 W
AC input
120 V
240 V
Max. watts
46.8 W
33.2 W
Max. amps.
0.486 A
0.22 A
Power factor
97.71 W/VA
94.8 W/VA
Max. volt-ampere
47.89 VA
35.02 VA
Typical watts
37.44 W
26.56 W
BTU (typical)
127.67 BTU
90.56 BTU
Environmental specifications
This table summarizes the environmental requirements for the systems.
Specification
CX580 Desktop
CX780 Desktop
Operating acoustic
45 dBA Sound pressure (Typical)
45 dBA Sound pressure (Typical)
Temperature (operating)
0° to 45° C
32° to 113° F
0° to 45° C
32° to 113° F
Temperature (storage)
-40° to 65° C
-40° to 149° F
-40° to 65° C
-40° to 149° F
Relative humidity
20% to 80% noncondensing
20% to 80% noncondensing
Storage humidity
5% to 95% noncondensing
5% to 95% noncondensing